- 🌡️ SUPPLEMENTAL TERRARIUM HEAT: The 4-watt heating mat provides a localized source of gentle warmth for compatible 1–5 gallon glass terrariums.
- 🦎 COMPACT 4 × 7-INCH SIZE: Designed for reptile, amphibian, invertebrate, plant and suitable small-animal enclosures where only a small heated zone is required.
- 🔥 PTC HEATING MATERIAL: Updated heating material and insulation distribute warmth across the mat while using 4 watts of electrical power.
- 🧲 STRONG ADHESIVE BACKING: The integrated adhesive layer secures the mat to a clean exterior glass surface for direct contact and efficient heat transfer.
- 🔌 120V US PLUG AND 6-FOOT CORD: Includes a standard North American plug and an extended power cable. A thermostat is not included and should be purchased separately when required.
iPower 4 × 7-Inch Reptile Heating Pad
The iPower reptile heat mat is a compact 4-watt heater designed to provide supplemental warmth to a compatible glass terrarium. Its 4 × 7-inch heating area is listed for enclosures between 1 and 5 gallons.
The pad attaches to the exterior of the terrarium using its adhesive backing. It may be mounted beneath an elevated glass tank or on an exterior side wall, depending on the enclosure, animal and manufacturer’s installation instructions.
Localized Warmth for Small Terrariums
Reptiles, amphibians and invertebrates depend on environmental temperatures to regulate their body functions. A heat mat can create a localized warm area, allowing the animal to move between warmer and cooler sections of the enclosure.
The mat should heat only part of the habitat. Covering the entire base can prevent the animal from moving away from excessive warmth.
Supplemental Heat Source
This 4-watt mat may be suitable as a supplemental heat source for compatible setups, but it may not provide all the heat required by every species.
Heating requirements depend on:
- Animal species and life stage
- Enclosure size and construction
- Room temperature
- Ventilation
- Substrate type and depth
- Mounting position
- Seasonal temperature changes
- Additional heating or lighting equipment
Research the correct temperature range for the specific animal before installing any heating device.
4-Watt PTC Heating Design
The mat uses updated PTC heating material and insulation intended to distribute warmth across its surface.
According to the manufacturer, when tested at an ambient temperature of approximately 68°F (20°C), the mat surface reached about 80°F (26.7°C). This result was recorded under experimental conditions and is not a guaranteed operating temperature.
Actual Temperature Will Vary
Surface and enclosure temperatures can change according to:
- Room temperature
- Air circulation
- Glass thickness
- Substrate depth
- Enclosure placement
- Thermostat setting
- Insulation around the tank
- Duration of operation
Never estimate the habitat temperature by touching the exterior glass. Use accurate measuring equipment inside the enclosure.
Thermostat Not Included
The selected “Heat Pad” version does not include an adjustment knob or thermostat.
For controlled operation, connect the mat to a compatible reptile thermostat rated for the heater’s voltage and wattage. Position and configure the thermostat probe according to the thermostat and enclosure instructions.
A thermostat regulates the heat source, while a separate digital thermometer verifies the actual temperature. Using both provides better monitoring than relying on either device alone.
Adhesive Exterior Mounting
Preparing the Glass
The adhesive backing is intended to hold the pad against the exterior contact area of a standard glass terrarium.
Before installation:
- Unplug the heat mat.
- Empty or safely secure the enclosure.
- Choose the exterior mounting location.
- Clean dust, grease and residue from the glass.
- Allow the surface to dry completely.
- Check that the mat and cable are undamaged.
- Plan the power-cord route before removing the backing.
Apply the pad carefully because repositioning it after adhesion may weaken the bond or damage the heating element.
Exterior Use Only
Do not place the mat inside the habitat where it can contact the animal, substrate or water.
Do not install it on plastic, acrylic, wood or another material unless the enclosure and heat-mat manufacturers explicitly confirm compatibility.
The product description specifically identifies standard glass terrariums as the intended enclosure type.
Bottom or Side Installation
The manufacturer permits under-tank use when the terrarium is correctly elevated, but warns that trapped heat creates a fire risk.
Under-Tank Installation
When mounting beneath a glass terrarium:
- Attach the mat to the exterior glass only.
- Use the supplied rubber feet to elevate the enclosure.
- Maintain airflow beneath the tank.
- Never place the heated tank directly on a table, floor or carpet.
- Keep the power cord free from pinching and crushing.
- Follow the enclosure manufacturer’s guidance for under-tank heating.
Side Mounting
The manufacturer identifies exterior side mounting as the preferred option when safe bottom mounting is uncertain.
Side mounting may also be more suitable for enclosures with deep substrate because excessive substrate can reduce useful heat transfer from below.
Always monitor both the heated area and the cooler side after installation.
Creating a Temperature Gradient
A properly arranged enclosure should allow the animal to move away from the heated zone.
Monitor Multiple Locations
Measure the temperature at:
- The warm hide or heated zone
- The substrate surface
- The cooler side of the enclosure
- Any area where the thermostat probe is positioned
Allow the system to operate and stabilize before introducing an animal.
Avoid Direct Contact Burns
The animal must not be able to touch the heating mat directly. Check that the interior glass or substrate surface does not exceed the safe range for the species.
Seek guidance from an exotic-animal veterinarian if the animal has burns, abnormal behaviour, prolonged hiding, weakness or signs of heat stress.
Suitable Applications
The manufacturer lists the heating mat for compatible:
- Reptile terrariums
- Amphibian enclosures
- Invertebrate habitats
- Small-animal setups
- Plant terrariums
- Seed germination projects
- Home-brewing applications
Suitability depends on the required temperature, enclosure material and monitoring system. Use the mat only when its specifications match the intended application.
Reptile and Amphibian Use
A heat mat does not supply UVB light, visible daylight or overhead basking radiation. Species requiring those environmental elements need appropriate equipment in addition to the mat.
Humid Environments
The pad is described as water- and moisture-resistant, but it is not submersible.
Keep the plug, electrical connection and damaged cable away from water. Do not use the pad if moisture has entered an electrical component.
Electrical and Fire Safety
Prevent Heat Entrapment
The manufacturer warns of a fire risk if heat becomes encapsulated.
Never:
- Fold, crease, cut or puncture the mat
- Place it inside the enclosure
- Cover it with insulating material
- Sandwich it tightly between solid surfaces
- Place an under-heated tank directly on carpet or furniture
- Operate it with a damaged cord or plug
- Immerse it in water
- Use it without the required ventilation space
Safe Operation
Follow the current product manual and electrical instructions. Plug the mat into a correctly installed 120V outlet and keep the connection dry.
The manufacturer instructs users to avoid prolonged unattended use and not to fall asleep while the pad is operating. If temperature regulation is required, use a suitable thermostat while continuing to follow the product’s safety directions.
Unplug the mat immediately if you notice:
- Burning odour
- Smoke
- Discoloration
- Cracking or bubbling
- Unusual hot spots
- Damaged insulation
- A loose electrical connection
- Failure of the adhesive mounting
Cleaning and Maintenance
Cleaning the Exterior
Unplug the pad and allow it to cool completely before cleaning.
The surface may be gently wiped or scrubbed, but the mat must never be immersed in water. Keep moisture away from the plug, cable entry and electrical connection.
Routine Inspection
Check the following regularly:
- Adhesive bond
- Cable insulation
- Plug condition
- Mat surface
- Terrarium glass
- Rubber support feet
- Ventilation gap
- Thermostat function
- Recorded enclosure temperatures
Do not continue using a pad that has detached, cracked, overheated or developed electrical damage.
Product Specifications
- Brand: iPower
- Product type: Under-tank terrarium heat mat
- Selected size: 4 × 7 inches
- Power: 4 watts
- Recommended enclosure size: 1–5 gallons
- Voltage: 120V
- Plug type: Standard North American plug
- Power-cord length: Approximately 6 ft
- Heating technology: PTC heating material
- Mounting method: Adhesive exterior attachment
- Intended enclosure material: Standard glass terrarium
- Water resistance: Moisture-resistant; not submersible
- Thermostat included: No
- Colour: Black
- Model number: XHC-F034D
- Manufacturer: iPower
Important Safety Information
This product is an electrical heat source and can cause burns, glass damage or fire if installed incorrectly.
Use the supplied rubber feet when mounting beneath a terrarium and maintain unobstructed airflow below the enclosure. If safe bottom installation is uncertain, follow the manufacturer’s recommendation to use exterior side mounting.
Verify temperatures with reliable instruments and provide a cooler area where the animal can move away from the heat. Do not use the mat as a substitute for species-specific husbandry, professional advice or veterinary care.
